Welcome Guest!!

Welcome to SCCX, for full access to the forums, please register and join our community, it's free.

Author Topic: SuperSlideStyle  (Read 71651 times)

Toro

  • Hero Member
  • *****
  • Posts: 2066
  • 4wd Pts: 126
  • yep, Dos XX and Chipotle
Re:
« Reply #30 on: December 23, 2014, 06:46:59 PM »
Fair enough.

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #31 on: December 24, 2014, 06:56:03 PM »
These tires look great but they are very loud at very low speed, like cruising in a parking lot.  You can hear every knub.  They are actually quiet on the freeway.  No drone inside the cabin.
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

knightrider

  • Administrator
  • Hero Member
  • *****
  • Location: San Diego, CA
  • Posts: 2527
  • 4wd Pts: 228
    • 2016 Pro4x
Re:
« Reply #32 on: December 24, 2014, 08:08:45 PM »
I use my locker more in 2hi than 4lo, next mod is rear shock tower through the cargo floor :)
Jordan - K6XTE
2012 Knight Armor Xterra Pro-4X - Sold :(
2016 GunMetal Frontier Pro-4X with AT Summit

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #33 on: May 13, 2015, 07:18:13 AM »
Has anyone experienced any luck changing to HD front springs AND 1.5" spacers with the stock A-arms?
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

CAWoody

  • Hero Member
  • *****
  • Location: Evergreen, CO
  • Posts: 970
  • 4wd Pts: 72
    • 2018 Toyota Tacoma (Really miss the X)
Re: SuperSlideStyle
« Reply #34 on: May 13, 2015, 02:22:59 PM »
Just adding the spacer with stock UCA's was a pain, can't imagine what it would be like with heavy springs. Good luck.
Be careful when you follow the masses..... sometimes the "M" is silent.

Ghost65

  • Old-Schooler
  • Hero Member
  • *****
  • Location: East of You
  • Posts: 862
  • 4wd Pts: -476
    • 2019 Ready Mix Taco
Re: SuperSlideStyle
« Reply #35 on: May 14, 2015, 11:21:27 AM »
Thought I read somewhere not to combine spacers and HD springs?


Sent from Planet Claire
 using Tapatalk
KD6DCI

Once again, I must state for the record: We are not a club, we are enablers for your addiction.

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #36 on: May 14, 2015, 04:31:30 PM »
Would I need to upgrade my lower control arms at this point then, before I get the spacers?
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

Ghost65

  • Old-Schooler
  • Hero Member
  • *****
  • Location: East of You
  • Posts: 862
  • 4wd Pts: -476
    • 2019 Ready Mix Taco
Re: SuperSlideStyle
« Reply #37 on: May 14, 2015, 05:18:08 PM »
Would I need to upgrade my lower control arms at this point then, before I get the spacers?

Irwin...find out what type of HD springs you are looking at.  Are they stock length HD springs, or longer?  If they are stock, you may be able to use the spacers.

If the springs are longer, which means they also provide lift as well as stiffer spring rate, then no, you don't want to use the spacers.  Longer springs and spacers will make the truck difficult, if not impossible to align.  Which is when you upgrade the upper control arms, not the lower.

Think of it like this:

Stock height springs, add spacers for lift.

Taller springs, no spacers and possible UCA upgrade.

Hope this helps!
KD6DCI

Once again, I must state for the record: We are not a club, we are enablers for your addiction.

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #38 on: July 10, 2015, 12:03:59 PM »
Finally got around to welding in the new sliders/sidesteps for my X.  Been wanting to do it for a year or so.

 [ You are not allowed to view attachments ]
 [ You are not allowed to view attachments ]
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #39 on: July 10, 2015, 12:10:09 PM »
Also going to add 2 - 12" LED light bars but not sure if on the bumper or to the roof...

 [ You are not allowed to view attachments ]
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #40 on: July 12, 2015, 07:38:29 PM »
Here is the pre-runner style light bar prototype.

 [ You are not allowed to view attachments ]
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

Toro

  • Hero Member
  • *****
  • Posts: 2066
  • 4wd Pts: 126
  • yep, Dos XX and Chipotle
Re:
« Reply #41 on: July 19, 2015, 08:02:00 PM »
Sporting the XOC colors... cool!
    I used to run a ZEX fogger and an ACT clutch on my b13. Our tool boxes are similar.

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #42 on: September 16, 2015, 06:30:12 PM »
Yeah, I used to have a 240SX track car used for Drifting, Time Attacks, & Time Trials.  Hence the name "SuperSlideStyle".
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #43 on: February 24, 2016, 08:07:04 PM »
Ok, so, I got both sliders finally welded in place on the 2013 X.  Still working on a prototype pre-runner style light bar for thr front grill.  Pics are coming.  Also going to start a Gobi style hatch ladder soon.
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

SuperSlideStyle

  • Hero Member
  • *****
  • Location: Fontana, CA (Inland Empire)
  • Posts: 1788
  • 4wd Pts: 19994
  • Are we ready? Not really but here we go!
    • 2013 Nissan Xterra PRO-4X
Re: SuperSlideStyle
« Reply #44 on: May 23, 2016, 09:36:25 AM »
Found these 2.25-3"  tube-mount accessory brackets at O'Reileys Auto Parts.  Seem very nice so far.  Stainless steel hardware will still need anti-seize compund applied to it.

 [ You are not allowed to view attachments ]
2013 Xterra Pro4X 6 spd
2022 Acura MDX SH-AWD

 


Powered by EzPortal